Download Schulze Elektronik Port Devices Drivers
Download Schulze Elektronik Port Devices Driver Ed
Download Schulze Elektronik Port Devices Driver License

Digital inputs/outputs
DI6 DO6 IOL2 (IRT)
Ethernet 10/100 Mbit/s; Push Pull RJ45 Data connector
Push Pull Power connector, max. 12 A
M12, 5-pole, A-coded
Galvanic isolation
Connection cables are in the online shop under 'Connection Technology'.
Housing fully potted.

Protection	IP67
Mounting method	2-hole screw mounting
Temperature range	0...+55 °C (storage temperature -20...+70 °C)
Dimensions H×W×D	42.7×63×225 mm

No USB drivers should need downloading as when you plug the DV4mini into your USB port Windows will find and download it. This can take some time so when you plug your DV4mini into your PC, do not unplug it until its finished: When you first plug the DV4mini into your USB port. (This can take up to half a hour to find the driver). Download Installation Instructions 55516inax13.zip Download Manuals 55516hdbx12.zip Download Software and driver 10501019IO-Link-Device-ToolTRBx48.zip.

Output

Download Schulze Elektronik Port Devices Driver

Actuator supply UA	24 V DC (EN 61131-2), max. 12 A
Switching current per output	max. 2 A (short-circuit and overload protected)
Lamp load	10 W

Sensor supply US	24 V DC (EN 61131-2), max. 200 mA (M12 female)/max. 1 A (IO-Link female), short-circuit and overload protected
Type	for 3-wire sensors or mechanical switches, PNP, IO-Link Devices

IO-Link

IO-Link	2× Master
Operating modes	COM1; COM2; COM3 (automatic)
Transfer parameters	32 Byte (per IO-Link port)
Port Class	Class B (galvanically separated)
Specification	IO-Link Master V1.12

PIN 4	Input (port X3...X5); Output (port X0...X2); IO-Link Master (port X6, X7)
PIN 2	Input (port X3...X5); Output (port X0...X2); U-Actuator IO-Link Class B (port X6, X7)

Connections

Fieldbus	Ethernet 10/100 Mbit/s; Push Pull RJ45 Data connector
Sensor-system/actuator supply	Push Pull Power connector, max. 12 A
I/O ports	M12, 5-pole, A-coded

FSU (Fast-Start-Up)	max. 500 ms
Shared Device/Input	yes, for 2 controls
PROFINET Netload Class	III
Specification	V2.3, Conformance Class C (IRT)
MRP	yes
Addressing	DCP

Diagnostic

Communication status	via LED
Diagnostic via LED	per module and channel
Diagnostic via BUS	per module and channel
Monitoring - under voltage	yes
Monitoring - no voltage	yes
Short-circuit and overload	yes
Actuator warning	per channel via LED and BUS
Cable break	per port

country of origin	DE
customs tariff number	85389099
EAN	4048879619974
eClass	27242604
Packaging unit	1

Power cableShow all

INTRODUCTION

Welcome! You just got a new Maker UNO and you are about to start your journey to learn coding and electronics. Every journey starts with the 1st step, so let’s treat this post as your 1st step into the world of coding and electronics. Let’s start making something!

In this post we will focus on:

Installing Arduino IDE Software
Installing USB-Serial Driver
Upload A Simple Sketch

To get started, you must have:

Laptop/PC

Connect your Maker UNO to your computer using a USB Micro B cable. The USB will also act as the power supply to your board. Keep it connected.

1. INSTALLING ARDUINO IDE SOFTWARE

Download the latest Arduino IDE at Arduino official website – www.arduino.cc/en/Main/Software. Choose the appropriate installer depending on your computer’s operating system (Windows, Mac OS or Linux). Complete the download, proceed with the installation as usual. (For Windows user, it is recommended to install the first option)

2. INSTALLING USB-SERIAL DRIVER

For Windows users, please follow these steps:

1. Download the CH341 Driver for Windows here

2. Double-click the “CH341SER” file that you have just downloaded.

3. Click “Install”.

4. Click “OK” when the driver is successfully installed.

5. Go to window search, search for “device manager”.

6. At “Device Manager”, expand “Ports (COM & LPT)”. Check which COM port the USB-Serial CH340 driver is being assigned to. For this example, it is COM5. Please take note of the COM number.

7. Connect Maker UNO to your computer. Launch Arduino IDE, go to Tools > Port > COM X (select COM port that you recognized in Step 6).

Download Schulze Elektronik Port Devices Drivers

For Mac users, please follow these steps:

1. Download the CH341 Driver for Mac here.

2. Double-click to unzip the downloaded file. Open the unzipped folder then double-click the pkg file.

3. Click “continue” to begin installation.

4. Once done, click “Restart” to restart your Mac.

5. After you have restarted your Mac, launch Arduino IDE. Choose the driver at Tools > Port > /dev/cu.wchusbserial1420. (please ensure that the Maker UNO is connected to your PC)

3. UPLOAD A SIMPLE SKETCH

1. To select the board model, go to Tools > Board > Arduino/Genuino Uno.

2. Let’s try one of the sample code given. Go to File > Example > 0.1 Basic > Blink.

3. Click the “Upload” button to upload the sample code to your Maker UNO.

4. Check your result!

RESOURCES AND GOING FURTHER

We have prepared a beginner-friendly learning guide to assist you to learn the basic function of Arduino on your own pace. Download learning guide here

Visit this page, if you would like to explore more interesting projects of Maker UNO,

For more information, check out the resources below:

PENGENALAN

Selamat datang, tahniah! Anda baru sahaja memiliki board Maker Uno dan anda akan mula pengembaraan untuk mempelajari elektronik dan cara untuk menulis kod. Setiap pengembaraan bermula dengan langkah pertama, jadi sila anggap post ini sebagai langkah pertama anda untuk ke dunia kod dan elektronik. Jom kita mula mencipta!

Dalam post ini, kita akan fokus kepada:

Cara install software Arduino IDE.
Cara install driver Maker Uno.
Memuat naik kod ringkas ke Maker Uno.

Untuk mula, anda perlu ada:

Laptop/PC

Sambungkan Maker Uno ke PC menggunakan kabel USB mikro B seperti yang tertera pada gambar di bawah. Sambungan USB juga bertindak sebagai bekalan kuasa ke board anda, jadi pastikan ianya